Blue B3 | Foil 12.5"x 25ft
SKU:
$6.95
$6.95
per item
PLEASE READ ALL INFORMATION FOR THIS FOIL BECAUSE IT IS APPLIED DIFFERENTLY THAN OTHER VINYL. AN ADHESIVE (EasyWeed Adhesive) IS NEEDED AND PURCHASED SEPARATELY.
Metallic look with Soft Feel / We stock over 70+ colors & designs of textile foils.
Metallic Foil Transfer is a special eye catching graphic effect for T-shirts. It produces a shiny “metal-appearing” surface on various types of fabrics by using a heat press or home iron.
Heat transfer Foils can be applied using a cuttable adhesive such as Siser EasyWeed Adhesive or Specialty Materials HotMelt
Application Instructions: (heat press)
• Cut (Adhesive) in reverse
• Weed excess material
• Preheat garment for 2-3 seconds
• Apply design at 275°F/135°C
• Use medium pressure for 5-10 seconds
• Peel carrier hot
Application instructions: (home iron)
• Cut (Adhesive) in reverse
• Weed excess material
• Set iron dial between Cotton and Linen
• Cover design with teflon sheet or parchment paper
• Place on flat hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 10-15 seconds
• If areas of design lift after application, replace cover sheet and re-press for 5 seconds
• Peel carrier hot
Application instructions: (HTV textile foil)
• Trim the foil 1/2" to 1" inch bigger than the designed image
• Place foil over top of the image / must be applied shiny side up.
• Cover Foil with Teflon Sheet
• Heat press 10-15 sec. at 300-325° F / Medium even pressure
• Cool Peel Foil / Rub with a cloth, let cool completely, then peel.
Care instructions:
• wait 24 hours after application to wash
• do not dry clean
• machine wash normal cycle, cold/warm with mild detergent
• lay flat to dry or machine dry on low/normal setting
• do not use chlorine bleach
These are the same foils used by Screen Printers.
Metallic look with Soft Feel / We stock over 70+ colors & designs of textile foils.
Metallic Foil Transfer is a special eye catching graphic effect for T-shirts. It produces a shiny “metal-appearing” surface on various types of fabrics by using a heat press or home iron.
Heat transfer Foils can be applied using a cuttable adhesive such as Siser EasyWeed Adhesive or Specialty Materials HotMelt
Application Instructions: (heat press)
• Cut (Adhesive) in reverse
• Weed excess material
• Preheat garment for 2-3 seconds
• Apply design at 275°F/135°C
• Use medium pressure for 5-10 seconds
• Peel carrier hot
Application instructions: (home iron)
• Cut (Adhesive) in reverse
• Weed excess material
• Set iron dial between Cotton and Linen
• Cover design with teflon sheet or parchment paper
• Place on flat hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 10-15 seconds
• If areas of design lift after application, replace cover sheet and re-press for 5 seconds
• Peel carrier hot
Application instructions: (HTV textile foil)
• Trim the foil 1/2" to 1" inch bigger than the designed image
• Place foil over top of the image / must be applied shiny side up.
• Cover Foil with Teflon Sheet
• Heat press 10-15 sec. at 300-325° F / Medium even pressure
• Cool Peel Foil / Rub with a cloth, let cool completely, then peel.
Care instructions:
• wait 24 hours after application to wash
• do not dry clean
• machine wash normal cycle, cold/warm with mild detergent
• lay flat to dry or machine dry on low/normal setting
• do not use chlorine bleach
These are the same foils used by Screen Printers.